-
1 straightness deviation in a plane
отклонение от прямолинейности в плоскости
Наибольшее расстояние EFL от точек реального профиля до прилегающей прямой в пределах нормируемого участка.
Частными видами отклонения от прямолинейности являются выпуклость и вогнутость.
Выпуклость - отклонение от прямолинейности, при котором удаление точек реального профиля от прилегающей прямой уменьшается от краев к середине.
Вогнутость - отклонение от прямолинейности, при котором удаление точек реального профиля от прилегающей прямой увеличивается от краев к середине.
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > straightness deviation in a plane
-
2 deviation
отклонение; отступлениеdeviation from true longitudinal section profile — отклонение профиля продольного сечения ( при измерении шероховатости поверхности)
deviation in cumulative lead — отклонение хода, накопленное отклонение хода ( резьбы);
deviation in dual flank lead — отклонение хода ( резьбы) по двум боковым сторонам
- admissible deviationdeviation in dual flank pitch — отклонение шага ( резьбы) по двум боковым сторонам
- angular deviation
- angularity deviation
- arithmetical average deviation from mean line
- arithmetical mean deviation of the profile
- aspheric deviation
- average deviation
- axial pitch deviation
- center distance deviation
- circular deviation
- circularity deviation
- coaxiality deviation
- conjugate deviation
- converted deviation
- cylindricity deviation
- deviation of a single bore diameter
- deviation of a single ring width
- deviation of average base tangent length
- deviation of base tangent length
- deviation of circularity
- deviation of constant chord height
- deviation of constant chordal tooth thickness
- deviation of dimension over balls
- deviation of dimension over pins
- deviation of measuring shaft angle of a gear pair
- deviation of parallelism
- deviation of perpendicularity
- deviation of pitch
- deviation of position
- deviation of the actual bearing height
- deviation of the actual bearing width
- deviation of tip angle
- deviation of tip diameter
- dimensional deviation
- flatness deviation
- form deviation
- fundamental deviation
- helix deviation
- instantaneous deviation
- line profile deviation
- local deviation from straightness
- lower deviation
- maximum deviation
- mean bore diameter deviation
- mean deviation
- mean outside diameter deviation
- measured deviation
- minimum deviation
- minor deviation
- multiple deviation
- peak-to-peak deviation
- peak-to-valley deviation
- positional deviation
- profile deviation in M system
- profile deviation
- pump capacity deviation
- rms deviation
- root-mean-square deviation
- shaft angle deviation
- significant deviation
- single plane mean bore diameter deviation
- single plane mean outside diameter deviation
- size deviation
- squared deviation
- standard deviation
- steady-state deviation
- surface profile deviation
- sustained deviation
- system deviation
- transient deviation
- true deviation
- upper deviationEnglish-Russian dictionary of mechanical engineering and automation > deviation
См. также в других словарях:
отклонение от прямолинейности в плоскости — Наибольшее расстояние EFL от точек реального профиля до прилегающей прямой в пределах нормируемого участка. Частными видами отклонения от прямолинейности являются выпуклость и вогнутость. Выпуклость отклонение от прямолинейности, при котором… … Справочник технического переводчика
KABBALAH — This entry is arranged according to the following outline: introduction general notes terms used for kabbalah the historical development of the kabbalah the early beginnings of mysticism and esotericism apocalyptic esotericism and merkabah… … Encyclopedia of Judaism
Buckling — In engineering, buckling is a failure mode characterized by a sudden failure of a structural member subjected to high compressive stresses, where the actual compressive stress at the point of failure is less than the ultimate compressive stresses … Wikipedia
winding — winding, sinuous, serpentine, tortuous, flexuous can all mean curving first one way and then another. Winding, the general and the ordinary term, often implies spiral ascent {winding stairs} {a winding mountain road} When applied to things in a… … New Dictionary of Synonyms